Steel Grating Standards-Euro, USA, UK

Our metal and steel grating products are produced according to UK, Euro, American and other related international standards. Some are listed below:
Steel Grating Standard Steel Material Standard Hot Dip Zinc Coating Standard
China Standard:
YB/T4001—1998

China Standard:
GB700—88 

China Standard:
GB/T13912-92

USA Standard:
ANSI/NAAMM(MBG531—88)
USA Standard:
ASTM(A36)
USA Standard: ASTM(A1 23)
UK Standard: BS4592—1987 UK Standard: BS4360(43A) UK Standard: BS729
Australia Standard: ASl 657—1 992 Australia Standard: AS3679 Australia Standard: ASl650

AMERICAN NATIONAL STANDARD, ANSI/NAAMM STANDARD is set by American National Standard Institute and National Association of Architectural Metal Manufacturers.

Metal Bar Grating Manual For Steel, Stainless Steel, and Aluminum Gratings and Stair Treads, refer to PDF for details: ANSI/NAAMM MBG 531-17 .

Metal Grating Panels for Floorings and Steps Euro Standard

Metal grating structural design standards:
- UNI 11002-1:2009:
Design codes: Metal grating panels for floorings and steps - Part 1: Terminology, tolerances, requirements and test methods for panels for use in floorings in vehicular and pedestrian areas.

- EN 1990:2006
Eurocode 0 - Basis of structural design
- EN 1991-1-1:2004
Eurocode 1: Actions on structures - Part 1-1: General actions - Densities, self-weight, imposedloads for buildings;
- EN 1991-1-2:2004
Eurocode 1: Actions on structures - Part 1-2: General actions – Action on structures exposed tofire;
- EN 1991-1-3:2015
Eurocode 1: Actions on structures - Part 1-2: General actions – Snow loads;
- EN 1991-1-4:2010
Eurocode 1: Actions on structures - Part 1-4: General actions - Wind actions;
- EN 1991-1-5:2004
Eurocode 1: Actions on structures - Part 1-4: General actions – Thermal actions; tensioncomponents.
- EN 1993-1-1:2005
Eurocode 3 Design of steel structures - Part 1-1: General rules and rules for buildings
- EN 1993-1-2:2005
Eurocode 3 Design of steel structures - Part 1-2: General rules - Structural fire design
- EN 1993-1-3:2007
Eurocode 3 Design of steel structures - Part 1-3: General rules - Supplementary rules for coldformed members and sheeting – English.
- EN 1993-1-8:2005
Eurocode 3: Design of steel structures - Part 1-8: Design of joints
- EN 1993-1-12:2007
Eurocode 3 Design of steel structures - Part 1-12: Additional rules for the extension of EN 1993 upto steel grades S 700 – English.
- EN 1994-1-2:2005
Eurocode 4 Design of composite steel and concrete structures - Part 1-2: General rules- Structuralfire design
- EN 1994-2:2006
Eurocode 4 Design of composite steel and concrete structures - Part 2: General rules and rules forbridges – English.
- EN 1993-1-10:2005
Eurocode 3 Design of steel structures - Part 1-10: Material toughness and through-thicknessproperties.
- EN 1993-1-11:2007 - Eurocode 3 Design of steel structures - Part 1-11: Design of structures


Cutting processes

- DIN 2310:Thermal cutting - Part 6: Classification, processes

Welded Connections for Gratings
- EN ISO 9692:Welding and allied processes - Recommendations for joint preparation - Part 1: Manual metal-arcwelding, gas-shielded metal-arc welding, gas welding, TIG welding and beam welding of steels(ISO 9692-1:2003)
- EN 287-1 :Approval Testing of welders - Fusion welding - Part 1: Steels
- EN 288-2 :Specification and approval of welding procedures for metallic materials. Part2 Welding procedurespecification for arc welding.
- EN 288-3 :Specification and approval of welding procedures for metallic materials. Part3 Welding proceduretests for arc welding of steels.
- EN 571-1:Non-destructive testing - Penetrant testing - Part 1: General principles
- EN 970(1997) :Non destructive examination of fusion welds – Visual examination.
- EN 1291 :Non destructive examination of welds – Magnetic particle testing of welds – Acceptance levels.
- EN 1712 : Non destructive testing of welds - Ultrasonic testing of welded joints – Acceptance levels
- EN 1713 : Non destructive examination of welds - Ultrasonic examination – Characterization ofindications in welds.
- EN 1714 :Non destructive examination of welds - Ultrasonic examination of welded joints.
- EN 5817 :Welding - Fusion - welded joints in steel, nickel, titanium and their alloys (beam welding excluded)- Quality levels for imperfections.
- DIN EN ISO 17636-2:Non-destructive testing of welds - Radiographic testing - Part 2: X- and gamma ray techniqueswith digital detectors.
- ANSI / AWS
- D1.1 / 2000:Electrodes check.

Grating Bolted Connections
- EN ISO 4759-1:2001Tolerance for fasteners - Bolts, screws, studs and nuts - Product grades A,B and C.
- EN ISO 898-1:2001Mechanical properties of fasteners made of carbon steel and alloy steel - Bolts, screws and studs.
- EN 20898-2:1994Mechanical properties of fasteners. Nuts with specified proof load values. Coarse thread.
- EN ISO 898-6:1996Mechanical properties of fasteners. Nut with specified proof load values. Fine pitch thread.
- EN 20898-7:1996Mechanical properties of fasteners. Torsional test and minimum torques for bolts and screws withnominal diameters 1 mm to 10 mm.

Corrosion Protection
- DIN EN ISO 12944:Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part3: Design considerations (ISO 12944-3:1998)

Fire Protection meeting following or samilar standard:
- Greek National Code for Fire Resistance
- EN 13381-8:2013Test methods for determining the contribution to the fire resistance of structural members - Part8: Applied reactive protection to steel members

Steel Grating Standard Specification

Steel grating is commonly made of flat steel panel and supporting bars welded together with setting spacings. It goes through cutting, opening, edging and other processes. The popular vertical bar grating spacing is 30mm, 40mm or 60mm, horizontal bar grating is 50mm or 100mm normally. Details information please refer to the specification List below.

Surface Treatment: hot-dipped galvanized or electro galvanized mild steel.

Features:
The products enjoy the features of high strength, light structure, high bearing, convenience for loading and other properties.

Applications:
Steel grating is widely used in the platform, flooring, corridor, bridge, well covers, stairs, fencing for petroleum, chemical, power plant, waste treatment plant, civil engineering projects and environmental projects.

Steel Grating Specification Steel Bar Grating Flooring

Common Specification:

Verticle Bar Spacing Horizontal Bar Spacing Specification of Supporting Flat Steel (Width X Thickness)
20 × 3 25 × 3 32 × 3 40 × 3 20 × 5 25 × 5
30 100 G203 / 30 / 100 G253 / 30 / 100 G323 / 30 / 100 G403 / 30 / 100 G205 / 30 / 100 G255 / 30 / 100
50 G203 / 30 / 50 G253 / 30 / 50 G323 / 30 / 50 G403 / 30 / 50 G205 / 30 / 50 G255 / 30 / 50
40 100 G203 / 40 / 100 G253 / 40 / 100 G323 / 40 / 100 G403 / 40 / 100 G205 / 40 / 100 G255 / 40 / 100
50 G203 / 40 / 50 G253 / 40 / 50 G323 / 40 / 50 G403 / 40 / 50 G205 / 40 / 50 G255 / 40 / 50
60 50 - G253 / 60 / 50 G253 / 60 / 50 G403 / 60 / 50 G205 / 60 / 50 G255 / 60 / 50
Verticle Bar Spacing Horizontal Bar Spacing Specification of Supporting Flat Steel (Width X Thickness)
32 × 5 40 × 5 45 × 5 50 × 5 55 × 5 60 × 5
30 100 G325 / 30 / 100 G405 / 30 / 100 G455 / 30 / 100 G505 / 30 / 100 G555 / 30 / 100 G605 / 30 / 100
50 G325 / 30 / 50 G405 / 30 / 50 G455 / 30 / 50 G505 / 30 / 50 G555 / 30 / 50 G605 / 30 / 50
40 100 G325 / 40 / 100 G405 / 40 / 100 G455 / 40 / 100 G505 / 40 / 100 G555 / 40 / 100 G605 / 40 / 100
50 G325 / 40 / 50 G405 / 40 / 50 G455 / 40 / 50 G505 / 40 / 50 G555 / 40 / 50 G605 / 40 / 50
60 50 G325 / 60 / 50 G405 / 60 / 50 G455 / 60 / 50 G505 / 60 / 50 G555 / 60 / 50 G605 / 60 / 50

Find Us

Qindelin Steel Grating Engineering Corporation
Add: New Development Zone, Dezhou, Shandong, China
URL: https://www.steelgrating.org
Email: sale@steelgrating.org

2022 © Qindelin Steel Grating Engineering Corporation